Biology

A $450 3D printer builds living materials more than 100 layers tall

Anne Meyer's lab at the University of Rochester replaced the filament extruder with a syringe pump and added a support gel that keeps printed bacteria alive for four weeks or more.

By Letizia Giugliano
4 min read

ShareLinkedInFacebookX

A $450 3D printer builds living materials more than 100 layers tall
Photo: Smithsonian / Unsplash

A biology lab at the University of Rochester has turned a standard plastic 3D printer into a bioprinter for $450, and used it to print living materials more than 100 layers high. The same machines built by hobbyists and schools can now produce structures that cost upward of $100,000 with commercial bioprinters, the team reports in ACS Applied Polymer Materials. The trick is a syringe pump in place of the filament extruder, plus a gel the print sits in while it sets.

A syringe pump where the filament extruder used to be

Anne S. Meyer, a professor in the Department of Biology at the University of Rochester, has been building her own low-cost bioprinters for more than a decade. The latest version starts from an ordinary plastic printer: her team removed the filament extruder and fitted a syringe pump that pushes out bio-ink, a formula that mixes living cells with a polymer solution and hardens into a gel once printed Phys.org.

The syringe also pulls back, which stops the ink oozing at the edges of a print. "Our syringe can also perform both extrusion and retraction, preventing oozing at the edges of printed structures," Meyer said. The whole conversion cost $450, against $100,000 or more for a commercial bioprinter, and the parts are ordinary ones. Instructions for building the printer and the pump are published on GitHub Phys.org.

Read also on The Patent: Orbital Matter 3D Prints a 30 Centimeter Boom in Orbit · Sticky marine snow carries six times more carbon to the ocean floor

A cluttered workbench in a busy laboratory or workshop Photo: Daniel Miksha / Unsplash

The study, whose first author is Ram S. Gona, was done with colleagues from the University of Rochester and Cornell University and appeared in ACS Applied Polymer Materials (DOI: 10.1021/acsapm.6c01858). Meyer's stated aim is not a product but a recipe: "We aim to create DIY bioprinters using inexpensive, easily obtainable parts, so that they are affordable and easy for other scientists to make in their own labs as well" Phys.org.

“Our upgraded printer can create living structures that are significantly taller and more complex than was previously possible, and it can even create hollow cavities within the prints.”

— Anne S. Meyer, professor in the Department of Biology, University of Rochester, to Phys.org

The gel that holds the print up while it sets

Soft bio-ink collapses under its own weight before it firms up. The Rochester team solved that with a support gel, called a slurry, that the printer deposits into; it holds the ink in place and speeds setting at any height. The researchers made two versions: one that lets the finished print be lifted out easily, and one for incubation that keeps the microbes inside the print alive for four or more weeks. Under earlier methods, printed bacteria began dying after about nine days Phys.org.

A prototype hydrogel cylinder was printed into a calcium chloride slurry. Postdoctoral student Danielle Bennett examined the result in Meyer's lab. The longer incubation window matters for work on biofilms, the three-dimensional communities of microorganisms that stick to surfaces and can be either harmful or useful to humans. Meyer said the two incubation routes let her team "create engineered biofilm materials that either have more biofilm characteristics, allowing study of and testing on medically relevant biofilm, or that have stronger mechanical properties" Phys.org.

From under 20 layers to more than 100

Height was the previous limit. Earlier DIY bioprinters made structures of fewer than 20 layers; the upgraded machine reaches more than 100, and it can leave hollow cavities inside a print Phys.org.

Taller, hollow shapes raise the surface-to-volume ratio, the amount of contact area between the material and whatever surrounds it. Meyer argues this lets embedded bacteria take up signals and nutrients from the environment more efficiently and release useful products faster. Depending on which bacteria go into the ink, the resulting living material can clean contaminated water or break down waste such as plastic, applications that sit inside the broader push for sustainability in materials and waste treatment Phys.org.

The biology section of the work is the 3D printing side: the shape is chosen, not grown. A printed tissue is like a living tissue except that the researcher decides exactly which cells are inside it and what three-dimensional form they take.

No patent in the paper, and a blueprint anyone can copy

The publication describes no patent application or granted patent, and the source names no inventor filing. What it documents is a method made public: a peer-reviewed paper plus building instructions on GitHub, released so that other laboratories can copy the design rather than license it Phys.org.

That choice has a flip side worth watching. A published method, with parts and assembly described in the open, becomes prior art for anyone who later tries to claim the same combination of syringe pump, retraction and support slurry. The University of Rochester, Cornell and the journal have put the details in front of every lab that wants them, and the next step the source mentions is exactly that: other scientists building their own version.

AI-assisted article